Free on-site measure - one written quote before anything is booked
Edmonton, Alberta Loop pile and Berber Power-stretched

Berber Carpet Installation in Edmonton, AB

Berber and loop-pile carpet in Edmonton typically costs $3-$8 per sq ft installed, depending on the carpet grade, with stairs priced per tread. Carpet Installers Edmonton plans the seams at the measure so the loop rows line up, and seals every cut edge so a pulled loop can’t run.

$3-$8 per sq ft installed
Stairs priced per tread
Rows matched at every seam

Price your Berber install

Tell us about your project and we will get back to you within 24 hours.

What can we help with?

So the right crew reviews your project.

Or call (587) 404-4524

  • Free on-site measure
  • One written, itemised quote
  • Old flooring hauled away
  • (587) 404-4524

What loop pile asks of the fitter

Included

  • Included: Seams joined row to row: the loop rows on each side of a joint are pulled into line before the tape cools, so the seam reads as part of the pattern.
  • Included: Every cut edge sealed: A loop with a free end can pull and travel down the row. Edges are sealed as they are cut, not afterwards.
  • Included: A firm pad underneath: dense, low-profile padding stops the backing flexing underfoot, and that flexing is what breaks loops over the years.
  • Included: Stretched, not kicked: loop backing holds tension well, so a power-stretched room stays flat instead of rippling in the traffic lane.
  • Included: Old carpet and pad removed, split tack strip replaced
  • Included: Your offcuts left with you for future patches

Not included

  • Not included: Carpet cleaning (we install and repair, we don't clean)
  • Not included: Moving pianos, safes, water beds or full aquariums
Our Process

How a Berber job runs

1

Measure and map the rows

We measure each room and mark where a joint has to fall, running the rows with the daylight rather than across it.

2

Old floor out

Old carpet and pad come up, the tack strip is checked along every wall and the subfloor is swept flat.

3

Pad and strip down

Fresh dense pad is stapled off, and any tack strip that has lifted or split is replaced before the carpet goes near it.

4

Stretch, seam, tuck

The room is power-stretched, seams are bonded with the rows aligned, then edges are trimmed and tucked into the gully.

Questions about Berber carpet

Straight answers from the crew that measures and fits the job. If your question isn’t here, call or send the form and we’ll answer it.

Call (587) 404-4524
Why do seams show more on Berber than on plush carpet?

Loop pile has a row structure you can see from across the room, so a joint that is half a row out reads as a line. Plush hides the same joint in the pile. The fix is planning: we choose the seam position at the measure and align the rows as the seam is bonded.

A loop has pulled out. Does the whole room need replacing?

Rarely. A single pulled loop is cut flush with scissors and the loops beside it are secured. If the pull has travelled along the row, we cut in a small patch from an offcut, which is why we leave your leftovers with you.

What underpad goes under a Berber carpet?

A dense, low-profile pad. Thick soft padding feels luxurious in the shop but it lets the backing flex with every footstep, and that movement is what snaps loops and opens seams.

Can Berber go on a staircase?

Yes, and it wears very well there. The rows have to run straight over every nose and match tread to tread, so a Berber stair run takes longer to fit than the same square footage on a flat floor. We price stairs by the tread.

Is Berber a sensible choice for an Edmonton basement?

It handles traffic and furniture better than most cut piles, but a below-grade room needs a dry, level slab first. We look at the slab and the perimeter before we quote a basement, and say so if the floor is not ready.

Book a Berber measure in Edmonton

We measure the rooms, mark where the seams go and send back one written price.

Back to top